[Waterproof]
Approved under simulated heavy rain (100L/m²/h) for 3h.
Əsas menyu
Hədiyyə Kartlarını mağazamızdan əldə edə bilərsiniz
Əsas menyu
Kukilər siyasəti
Mən məxfilik siyasətində qeyd olunan şərtlərə uyğun olaraq məlumatlarımın işlənməsinə razılıq verirəm.Səbət
Səbətiniz boşdur
This sailing hat can replace a hood, freeing up the ears and helping you to be aware. The width of the brim stops water flowing into the collar of a jacket.
Yelkənli suya davamlı papaq 900 qara
8912748 / 58 sm / [smoked black]
28 Mall
Təhlükəsiz ödəniş
Biz həmçinin 150 avrodan yuxarı alış-verişlərdə 2, 3 və ya 4 dəfə ödəniş variantı təklif edirik.
Təhlükəsiz ödəniş
Biz həmçinin 150 avrodan yuxarı alış-verişlərdə 2, 3 və ya 4 dəfə ödəniş variantı təklif edirik.
Qaytarılma və dəyişdirilmə
Əşyalarınızı geri qaytarmaq üçün 90 gününüz var.
Əlavə məlumatı bu link vasitəsilə əldə edin.
Qaytarılma və dəyişdirilmə
Əşyalarınızı geri qaytarmaq üçün 90 gününüz var.
Əlavə məlumatı bu link vasitəsilə əldə edin.
Approved under simulated heavy rain (100L/m²/h) for 3h.
3-ply breathable laminated fabric (RET < 15)
Adjustment strap under the chin
This hat weighs around 100 grams
Təsvir
To find out whether a fabric is breathable, we test its evaporate resistance or RET (ISO 11092 standard). The lower the fabric’s resistance, the more moisture is evaporated, and therefore the higher the fabric’s breathability. We consider that if: RET < 9 = very breathable fabric 9 < RET < 12 = breathable fabric. The values for the Trek 500 jacket’s breathability are as follows: > More resistant fabric: RET < 12 (or 3621 g/m²/24 h, JIS1099A standard) > Lightest fabric: RET < 8 (or 2972 g/m²/2
Drying is a crucial phase in reactivating the water repellent treatment. We recommend that you lay your jacket flat on a clothes rack and leave it out to dry in the open. Caution: never dry your jacket directly on a radiator. Then place them in the tumble dryer on a short synthetics cycle, i.e. 10 to 15 minutes, before turning it back the right way round. Caution: do not over-dry the garment.
A fabric is water-repellent when water slides off the surface of the fabric, without seeping in. Your jacket does not become waterlogged and remains lightweight and breathable. The water-repellent properties are achieved with a treatment applied to the external side of the fabric, but in practice these properties can be altered. The water-repellent properties can be reactivated by putting the jacket in a dryer for 10 minutes at the lowest temperature.
We measure the resistance of a fabric to water pressure in mm of water column (based on ISO 811 ). The higher the water pressure withstood by the fabric, the more waterproof it is. Here are the waterproofing ratings: Component resistant to water pressure of 5000 mm after ageing (5 washes). This equates to 5,000 Schmerber average pressure exerted by the water during rain. The hat’s waterproof was tested in a rain shower with 100 litres of water/sqm/hour for 3 hours.
Waterproof components (water runs off the fabric) - 100% waterproof seams
Təsvir
To find out whether a fabric is breathable, we test its evaporate resistance or RET (ISO 11092 standard). The lower the fabric’s resistance, the more moisture is evaporated, and therefore the higher the fabric’s breathability. We consider that if: RET < 9 = very breathable fabric 9 < RET < 12 = breathable fabric. The values for the Trek 500 jacket’s breathability are as follows: > More resistant fabric: RET < 12 (or 3621 g/m²/24 h, JIS1099A standard) > Lightest fabric: RET < 8 (or 2972 g/m²/2
Drying is a crucial phase in reactivating the water repellent treatment. We recommend that you lay your jacket flat on a clothes rack and leave it out to dry in the open. Caution: never dry your jacket directly on a radiator. Then place them in the tumble dryer on a short synthetics cycle, i.e. 10 to 15 minutes, before turning it back the right way round. Caution: do not over-dry the garment.
A fabric is water-repellent when water slides off the surface of the fabric, without seeping in. Your jacket does not become waterlogged and remains lightweight and breathable. The water-repellent properties are achieved with a treatment applied to the external side of the fabric, but in practice these properties can be altered. The water-repellent properties can be reactivated by putting the jacket in a dryer for 10 minutes at the lowest temperature.
We measure the resistance of a fabric to water pressure in mm of water column (based on ISO 811 ). The higher the water pressure withstood by the fabric, the more waterproof it is. Here are the waterproofing ratings: Component resistant to water pressure of 5000 mm after ageing (5 washes). This equates to 5,000 Schmerber average pressure exerted by the water during rain. The hat’s waterproof was tested in a rain shower with 100 litres of water/sqm/hour for 3 hours.
Waterproof components (water runs off the fabric) - 100% waterproof seams
Composition
Composition
0 rəy
Üzv kartı
Please log in to view your member card.
Üzv kartı
Please log in to view your member card.
Üzv kartı
Please log in to view your member card.
Üzv kartı
Please log in to view your member card.